Menu

Pistols

View as Grid List
Sort by

Agency Arms 34 G3 Urban T-800 BW 2-Tone

$2,599.00 $2,339.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 17 G3 BONESAW SS Barrel

$2,550.00 $2,295.00

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 17 G3 BONESAW TiN Barrel

$2,550.00 $2,295.00

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 17 G3 BONESAW TiN Barrel

$2,450.00 $2,205.00

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 17 G3 Urban DLC SS Barrel

$2,399.00 $2,159.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 19 G4 OD Bonesaw Armor Stipple DLC

$2,399.00 $2,159.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 20 G4 Urban BW Bronze

$2,387.00 $2,148.30

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 20 Urban SS Match

$2,385.00 $2,146.50

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms M&P 9 FDE 2-Tone

$2,349.00 $2,114.10
Agency Arms presents a new build complete build package for the M&P platform. The build package includes many familiar features you see in our Glock builds. Each build also includes a set of custom Dawson Precision sights and Apex Tactical Specialties' internals for the trigger group. Slide Work All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed. This plate is designed in a way that enables one hand manipulation of the firearm that increases safety. We don’t do top serrations due to training issues with the masses. On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts. Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. Frame work We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill. We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol. With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster. We do a non traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling

Agency Arms Glock 34 Gen 3 DLC

$2,339.00 $2,105.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms Glock 19 Gen 4 URBAN TUNGSTEN

$2,330.00 $2,097.00

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 19 G4 Dark Earth Bonesaw DTF 2-Tone

$2,329.00 $2,096.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 19 G4 OD Bonesaw 2-Tone

$2,329.00 $2,096.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 17 G4 Grey Bonesaw 2-Tone Stipple

$2,329.00 $2,096.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 20 G4 Hybrid Tungsten

$2,312.00 $2,080.80
Slide Work All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed. This plate is designed in a way that enables one hand manipulation of the firearm that increases safety. We don’t do top serrations due to training issues with the masses. On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts. Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. ​ Internal Work We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring. We replace only one spring in the trigger system which is the plunger safety spring. The other springs are stock and will grant consistent primer strikes and positive reset. We use a factory OEM minus connector and tune the factory trigger bar. With all this work the pull weight will be 4-4.25 pounds depending on the pistol. We also manufacture our own trigger shoe which is flat with a curved toe. This fixes the issue of trigger/trigger guard finger and glove bite. Frame work We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill. We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol. With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster. We do a non traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 20 G4 Urban

$2,287.00 $2,058.30

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 20 G4 Urban

$2,287.00 $2,058.30

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 17 G4 OD Urban 2-Tone

$2,279.00 $2,051.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 34 G4 Urban DLC

$2,279.00 $2,051.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 17 G3 OD Bonesaw

$2,279.00 $2,051.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms Glock 34 Gen 3 DLC

$2,279.00 $2,051.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 34 G3 OD Urban DLC

$2,279.00 $2,051.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 19 G3 OD Bonesaw 2-Tone

$2,279.00 $2,051.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 19 G4 Green Frame Bonesaw DLC JARVIS Cut

$2,274.00 $2,046.60

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 19 G4 OD Hybrid Multicam

$2,259.00 $2,033.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 19 G4 OD Urban Multicam

$2,259.00 $2,033.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 19 G4 OD Urban Multicam

$2,259.00 $2,033.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 17 G4 OD Hybrid Multicam

$2,259.00 $2,033.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 26 G4 OD Hybrid Armor Stipple

$2,249.00 $2,024.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 17 G4 Urban BW Burnt Bronze

$2,249.00 $2,024.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 19 G4 Urban Midnight Bronze

$2,249.00 $2,024.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 17 G4 GREY Frame DLC

$2,249.00 $2,024.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms Glock 19 Gen 4 Green Frame BW Graphite

$2,249.00 $2,024.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms Glock 19 Gen 4 Green Frame BW Bronze

$2,249.00 $2,024.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

AGENCY ARMS GLOCK 17 GEN 4 Hybrid TiN

$2,249.00 $2,024.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 17 G4 GREY Frame DLC

$2,249.00 $2,024.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 17 G4 OD Urban Armor Stipple DLC

$2,249.00 $2,024.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms Glock 19 Gen 4 URBAN T-800

$2,230.00 $2,007.00

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 19 G3 OD Urban 2-Tone

$2,229.00 $2,006.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms M&P 9 BW Burnt Bronze

$2,219.00 $1,997.10
Agency Arms presents a new build complete build package for the M&P platform. The build package includes many familiar features you see in our Glock builds. Each build also includes a set of custom Dawson Precision sights and Apex Tactical Specialties' internals for the trigger group. Slide Work All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed. This plate is designed in a way that enables one hand manipulation of the firearm that increases safety. We don’t do top serrations due to training issues with the masses. On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts. Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. Frame work We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill. We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol. With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster. We do a non traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling

Agency Arms 26 G4 OD Bonesaw DLC

$2,199.00 $1,979.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 26 G4 Green Frame Bonesaw DLC

$2,199.00 $1,979.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 26 G 4 Tungsten

$2,199.00 $1,979.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 26 G 4 Tungsten

$2,199.00 $1,979.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 17 G4 OD Bonesaw DLC

$2,199.00 $1,979.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 19 G4 Urban Burnt Bronze

$2,174.00 $1,956.60

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 19C G4 Urban Comp DLC

$2,149.00 $1,934.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 19 G3 OD Bonesaw DLC

$2,149.00 $1,934.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 26 G4 OD Hybrid DLC

$2,149.00 $1,934.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

AGENCY ARMS GLOCK 17 GEN 4 URBAN BLACK

$2,149.00 $1,934.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

AGENCY ARMS GLOCK 17 GEN 4 URBAN BLACK

$2,149.00 $1,934.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 17 G4 Dark Earth Urban DLC

$2,149.00 $1,934.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 17 G4 Dark Earth Urban DLC

$2,149.00 $1,934.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 17 G4 Dark Earth Urban DLC

$2,149.00 $1,934.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 17 G4 Urban DLC

$2,149.00 $1,934.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 26 G4 DLC

$2,149.00 $1,934.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 26 G4 DLC

$2,149.00 $1,934.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 26 G4 DLC

$2,149.00 $1,934.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 26 G4 DLC

$2,149.00 $1,934.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 26 G4 DLC

$2,149.00 $1,934.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 19 Gen 4 Grey Frame DLC

$2,149.00 $1,934.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 19 G4 Green Frame Urban DLC

$2,149.00 $1,934.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 19 G4 OD Urban DLC

$2,149.00 $1,934.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 17 G4 Urban DLC

$2,149.00 $1,934.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 17C Urban DLC

$2,149.00 $1,934.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 17C Urban DLC

$2,149.00 $1,934.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 17 G3 OD Bonesaw DLC

$2,149.00 $1,934.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 19 G3 OD Bonesaw DLC

$2,149.00 $1,934.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 19C G4 Urban Comp DLC

$2,149.00 $1,934.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms M&P 9 Concrete Grey

$2,144.00 $1,929.60

Agency Arms presents a new build complete build package for the M&P platform. The build package includes many familiar features you see in our Glock builds. Each build also includes a set of custom Dawson Precision sights and Apex Tactical Specialties' internals for the trigger group.

 

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms M&P 9 Crushed Silver

$2,144.00 $1,929.60

Agency Arms presents a new build complete build package for the M&P platform. The build package includes many familiar features you see in our Glock builds. Each build also includes a set of custom Dawson Precision sights and Apex Tactical Specialties' internals for the trigger group.

 

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 19 G3 Urban Blue Titanium

$2,124.00 $1,911.60

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 19 G3 Urban Blue Titanium

$2,124.00 $1,911.60

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms M&P 9 Graphite Black

$2,119.00 $1,907.10

Agency Arms presents a new build complete build package for the M&P platform. The build package includes many familiar features you see in our Glock builds. Each build also includes a set of custom Dawson Precision sights and Apex Tactical Specialties' internals for the trigger group.

 

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms M&P 9 DLC

$2,119.00 $1,907.10
Agency Arms presents a new build complete build package for the M&P platform. The build package includes many familiar features you see in our Glock builds. Each build also includes a set of custom Dawson Precision sights and Apex Tactical Specialties' internals for the trigger group. Slide Work All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed. This plate is designed in a way that enables one hand manipulation of the firearm that increases safety. We don’t do top serrations due to training issues with the masses. On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts. Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. Frame work We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill. We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol. With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster. We do a non traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling

Agency Arms 26 G3 OD Hybrid Multicam

$2,109.00 $1,898.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Fowler G19 Gen3 MARK 2 TUNG BLK Match Barrel

$2,450.00 $1,890.00
Our Complete Package is the ultimate choice for shooting enthusiasts who want the most out of their firearms. The complete package includes the base firearm along with all the alterations that make the Mark 2 the premier enhanced Glock platform. Treatment includes full grip work, slide cuts and coating, polishing of internal parts, sight install, and optional match barrel fitment.

Fowler G19 Gen3 MARK 2 TUNG SS Match Barrel

$2,450.00 $1,890.00
Our Complete Package is the ultimate choice for shooting enthusiasts who want the most out of their firearms. The complete package includes the base firearm along with all the alterations that make the Mark 2 the premier enhanced Glock platform. Treatment includes full grip work, slide cuts and coating, polishing of internal parts, sight install, and optional match barrel fitment.

AGENCY ARMS GLOCK 17L GEN 3 Urban DLC

$2,099.00 $1,889.10
Gun Specific Options: -9mm Generation 3 -Urban -DLC Coating -Magwell -Agency Backplate -(2) 17rnd Magazines

Agency Arms 17 Gen 3 Urban DLC

$2,099.00 $1,889.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 19 G3 DLC

$20,990.00 $1,889.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 19 G3 DLC

$20,990.00 $1,889.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 19 G3 DLC

$20,990.00 $1,889.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 19 G3 DLC

$20,990.00 $1,889.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 17 G3 Urban DLC

$2,099.00 $1,889.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 17 G3 Urban DLC

$2,099.00 $1,889.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 17 G3 Urban DLC

$2,099.00 $1,889.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 19 G3 Urban Burnt Bronze

$2,024.00 $1,821.60

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 43 OD Hybrid 2-Tone

$2,010.00 $1,809.00

Internal Work

 

We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, and bevel out the inside area of the trigger guard on a mill.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 26 G3 OD Hybrid DLC

$1,999.00 $1,799.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 26 G3 DLC

$1,999.00 $1,799.10

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms TWC 19 PATROL SS Barrel

$1,900.00 $1,710.00

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

 We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring.  We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

AGENCY ARMS GLOCK 43 Hybrid DLC

$1,880.00 $1,692.00

Internal Work

 

We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, and bevel out the inside area of the trigger guard on a mill.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

AGENCY ARMS GLOCK 43 Hybrid DLC

$1,880.00 $1,692.00

Internal Work

 

We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, and bevel out the inside area of the trigger guard on a mill.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

AGENCY ARMS GLOCK 43 Hybrid DLC

$1,880.00 $1,692.00

Internal Work

 

We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, and bevel out the inside area of the trigger guard on a mill.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

OEM GLOCK 19 GEN 5

$699.00 $595.00

AGENCY ARMS BONESAW AUTHORIZATION FEE

$150.00 $135.00

Note: This is the ONLY way to order the "Bonesaw" cuts on a CUSTOMER SUPPLIED gun through Agency Arms.

We are accepting Authorization Fee's for Agency Arms to gunsmith a customer supplied Glock pistol finished in the Reactive Gunworks exclusive "Bonesaw" cut.

Customer Supplied Process:
1) Pay the "Bonesaw Authorization Fee" to Reactive Gunworks (each fee entitles you to the design rights for 1 pistol)

2) Using your Order Confirmation code from Reactive Gunworks, place your Bonesaw order directly with Agency Arms and pay the required 50% deposit (at www.AgencyArms.com)

3) Mail your Glock directly to Agency Arms (you will receive shipping instructions directly from Agency)

4) Upon completion of the gunsmithing by Agency Arms, pay the remaining balance due and Agency Arms will return ship your firearm.

How long will it take?
Build Times are provided by Agency Arms and are based off Demand.

Not available on subcompact (ie.G42/43) or long slide (ie.G34/17L) or large