Menu

Weapons

View as Grid List
Sort by

EraThr3 Lambo Bolt Action Rifles

$5,950.00
We're proud to offer the most refined rifles on the planet. And after months of R&D, we've developed multiple configurations that cover a broad range of requirements, yet focus on one thing... Absolute dominance in the marketplace. EraThr3 Lambo bolt guns are hand fit creations and glass-bedded one at a time. Driven by passion rather than a stress-case production manager, we cling to those old-school techniques while pushing the limits with modern day materials and technology. Meticulously built with the finest component parts available, each rifle is hand finished and proven on the range prior to delivery. These bolt action rifles provide a stable platform capable of long range work, and aggressive tactical operations. A lightweight, docile rifle, that can be shot day after day, engaging targets at 100-1000+ yards.

STI Costa Carry Comp

$3,599.00
STI continues its push for honest, game changing innovation with the introduction of the Costa Carry Comp. Its island comp BBL is machined from a single piece of stainless steel, which eliminates timing issues and the potential to come loose. The front sight is attached to the compensated BBL—making this the first ever barrel with a compensator in front of an island sight. The technology further reduces muzzle jump and enables you to keep eyes on the front sight rather than the blast of the comp. The comp reduces recoil by 63%. The STI RecoilMaster dual spring recoil system further reduces recoil, effectively making this the flattest, smoothest shooting pistol on the market.

EraThr3 Primo Special

$3,595.00
EraThr3 Primo Special E3 Accuracy Guarantee: Whether you are shooting steel, providing for the family, or hunting bad guys, we are here to support your efforts, and provide you the competitive edge required to prevail with a "Match Grade Rifle”. To achieve the expected level of accuracy, every unit is hand-crafted with extreme attention to detail in its fit, form, and function. Building an E3 rifle starts with a match grade barrel, chamber… and so on. We can guarantee the quality of our products and stand behind trusted suppliers to do the same, however we cannot guarantee the skill level of every shooter, quality of sub-par ammunition, and/or choice of optics & aftermarket accessories. Every rifle is tried, tested, and proven with Prime ammunition prior to delivery. This doesn't mean that our rifles won’t run with various types of ammunition, including custom loads or hunting grade products, it's just simply no guarantee that they will. Rifles, just like your favorite pair of pants, have a lifespan. Even with easy use, and great care, things break, wear-out, etc. We stand behind our goods, and will support them to the end. However, we also expect that you understand the definition of “normal wear and tear”. We highly recommend the training component to all of our customers, and follow the same advice ourselves. Being good at one’s craft takes good equipment, hard work, and dedication.

EraThr3 Nashville Rifle

$3,500.00
We're proud to offer the most refined rifles on the planet. And after months of R&D, we've developed multiple configurations that cover a broad range of requirements, yet focus on one thing... Absolute dominance in the marketplace. EraThr3 gas guns are assembled with a free-float handguard, single-point cut 416R PROOF Research barrel, and a hand-selected group of top top-notch component parts. Meticulously built on our own billet receivers, each assembly is hand finished and proven on the range prior to delivery.

STI Costa H.O.S.T.

$3,299.00
Featuring the new Vortex Viper® red dot, this gun is ready to run right out of the box. It’s the perfect H.O.S.T. weapon for anything you may want to mount on it. And the tall tritium sights co-witness with the halo for added options if needed. With a 4.15 barrel length and slim tactical magwell, it’s easily concealable and effectively functional.

EraThr3 Cali Special 5.56mm Rifle

$3,250.00
E3 Accuracy Guarantee: Whether you are shooting steel, providing for the family, or hunting bad guys, we are here to support your efforts, and provide you the competitive edge required to prevail with a "Match Grade Rifle”. To achieve the expected level of accuracy, every unit is hand-crafted with extreme attention to detail in its fit, form, and function. Building an E3 rifle starts with a match grade barrel, chamber… and so on. We can guarantee the quality of our products and stand behind trusted suppliers to do the same, however we cannot guarantee the skill level of every shooter, quality of sub-par ammunition, and/or choice of optics & aftermarket accessories. Every rifle is tried, tested, and proven with "Black Hills Match" ammunition prior to delivery. This doesn't mean that our rifles won’t run with various types of ammunition, including custom loads or hunting grade products, it's just simply no guarantee that they will. Rifles, just like your favorite pair of pants, have a lifespan. Even with easy use, and great care, things break, wear-out, etc. We stand behind our goods, and will support them to the end. However, we also expect that you understand the definition of “normal wear and tear”. We highly recommend the training component to all of our customers, and follow the same advice ourselves. Being good at one’s craft takes good equipment, hard work, and dedication.

EraThr3 16" Carbon Supreme

$3,250.00
We're proud to offer the most refined rifles on the planet. And after months of R&D, we've developed multiple configurations that cover a broad range of requirements, yet focus on one thing... Absolute dominance in the marketplace. EraThr3 gas guns are assembled with a free-float handguard, single-point cut 416R PROOF Research barrel, and a hand-selected group of top top-notch component parts. Meticulously built on our own billet receivers, each assembly is hand finished and proven on the range prior to delivery. su·preme /so͞oˈprēm/ adjective 1. (of authority or an office, or someone holding it) superior to all others. With blatant disregard to the masses, we set-out to design and build what "we" wanted in a modern-day AR-15. Rather than listen to some metrics pushing sales team, or rely on their boring market research data, we opted to do this one our way. And what we've found, is that those pencil pushers aren't always right. We're passionate about what we do, and what we do is win. Most every rifle out there is gonna go "bang", we get that part. This one just happens to do it with a new sense of style and greatness, one that you can have as well.

EraThr3 16" Stainless Rifle Custom Gray/Orange Distressed

$2,850.00
We're proud to offer the most refined rifles on the planet. And after months of R&D, we've developed multiple configurations that cover a broad range of requirements, yet focus on one thing... Absolute dominance in the marketplace. EraThr3 gas guns are assembled with a free-float handguard, single-point cut 416R PROOF Research barrel, and a hand-selected group of top top-notch component parts. Meticulously built on our own billet receivers, each assembly is hand finished and proven on the range prior to delivery.

USED DEMO Nighthawk Shadowhawk 9mm 5"

$3,995.00 $2,850.00
Approx 50-60 rounds fired. LOOKS BRANDNEW!!!

STI DVC Tactical DS

$2,799.00
Simply put, it’s built to shoot. The most functional competition gun features are purposefully combined to fit the defensive handgun shooter demands. Slide lightening cuts, threaded barrel, accessory rail, stippled grip, undercut trigger guard and higher capacity magazines are highly engineered to deliver dependability every time out. The DVC Series has set a precedent of functional superiority, and the DVC Tactical is no exception.

STI DVC LIMITED 9MM

$2,799.00
** For a limited time, all STI purchases will come with a free RDR Gear Custom Gun Holster and Magazine Carrier. The DVC Limited represents the latest custom quality innovations in STI design. Performance minded slide cuts enhance slide control, minimize forward recoil, and increase cycle rate. Added slide porting on the top and sides controls muzzle jump, and blends well with the overall DVC Limited appearance. The 5-inch bull barrel is finished with Titanium Nitride for wear resistance and improved lubricity. Responsive handling and control is had by way of specialty texturing done by Extreme Shooters to give the shooter enhanced grip and improved ergonomics. The sights are designed for quick reads and can be easily adjusted.

Agency Arms 17 Gen 4 Urban DLC

$2,480.00
Slide Work All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed. This plate is designed in a way that enables one hand manipulation of the firearm that increases safety. We don’t do top serrations due to training issues with the masses. On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts. Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. ​ Internal Work We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring. We replace only one spring in the trigger system which is the plunger safety spring. The other springs are stock and will grant consistent primer strikes and positive reset. We use a factory OEM minus connector and tune the factory trigger bar. With all this work the pull weight will be 4-4.25 pounds depending on the pistol. We also manufacture our own trigger shoe which is flat with a curved toe. This fixes the issue of trigger/trigger guard finger and glove bite. Frame work We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill. We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol. With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster. We do a non traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 26 G3 Black Multicam

$2,429.00

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

SAI M&P 9 - TIER ONE

$2,495.00
Introducing the Smith & Wesson Tier One Package the ultimate in performance and reliability for your M&P. The Tier One M&P features a trued mating of the frame and slide for optimal smooth tracking. This smooth and fast tracking is further enhanced through the reliable SAI weight reduction on the slide which is taken to the edge with the additional window cuts on the slide - only available on Tier Ones. The slide features enhanced deep rear cocking serrations for positive manipulations and the additional positive cocking serrations for press checks. The frame features a full hand stipple and double trigger guard undercut providing the user with a higher grip and added enhanced stippled surface for control. Customers have their choice of flat or traditional trigger shoes, and have their choice of TiN or Black Nitride stock barrels. If you want to take your M&P to another level of performance while still retaining that M&P reliability we all love this is the package for you!

War Sport GPR CC BLACK

$2,095.00
WAR SPORT GPR-CC: BASIC SPECS: CAL: .223 REM, WYLDE CHAMBER, 1:8 RH, QPQ MELONITE BARREL LENGTH: 16.0" (WITH GP-S COMP), OAL: 16.2" MID LENGTH DI GAS SYSTEM (Gas Tube & Low Pro Gas Block, QPQ MELONITE) WEIGHT (W/ 30-RD MAG): 7.5-LBS WEIGHT CARBINE: 6.5-LBS LENGTH OPEN: 35.5" LENGTH CLOSED: 32.75"

Agency Arms 17 G4 Grey Frame 2 Tone

$2,289.00
Slide Work All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed. This plate is designed in a way that enables one hand manipulation of the firearm that increases safety. We don’t do top serrations due to training issues with the masses. On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts. Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. ​ Internal Work We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring. We replace only one spring in the trigger system which is the plunger safety spring. The other springs are stock and will grant consistent primer strikes and positive reset. We use a factory OEM minus connector and tune the factory trigger bar. With all this work the pull weight will be 4-4.25 pounds depending on the pistol. We also manufacture our own trigger shoe which is flat with a curved toe. This fixes the issue of trigger/trigger guard finger and glove bite. Frame work We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill. We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol. With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster. We do a non traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 20 Urban SS Match

$2,285.00
Slide Work All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed. This plate is designed in a way that enables one hand manipulation of the firearm that increases safety. We don’t do top serrations due to training issues with the masses. On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts. Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. ​ Internal Work We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring. We replace only one spring in the trigger system which is the plunger safety spring. The other springs are stock and will grant consistent primer strikes and positive reset. We use a factory OEM minus connector and tune the factory trigger bar. With all this work the pull weight will be 4-4.25 pounds depending on the pistol. We also manufacture our own trigger shoe which is flat with a curved toe. This fixes the issue of trigger/trigger guard finger and glove bite. Frame work We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill. We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol. With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster. We do a non traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 19 G4 Urban BW Bronze DTF

$2,249.00
Slide Work All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed. This plate is designed in a way that enables one hand manipulation of the firearm that increases safety. We don’t do top serrations due to training issues with the masses. On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts. Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. ​ Internal Work We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring. We replace only one spring in the trigger system which is the plunger safety spring. The other springs are stock and will grant consistent primer strikes and positive reset. We use a factory OEM minus connector and tune the factory trigger bar. With all this work the pull weight will be 4-4.25 pounds depending on the pistol. We also manufacture our own trigger shoe which is flat with a curved toe. This fixes the issue of trigger/trigger guard finger and glove bite. Frame work We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill. We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol. With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster. We do a non traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Fowler G19 Gen3 MARK 2 TUNG BLK Match Barrel

$2,349.00
Our Complete Package is the ultimate choice for shooting enthusiasts who want the most out of their firearms. The complete package includes the base firearm along with all the alterations that make the Mark 2 the premier enhanced Glock platform. Treatment includes full grip work, slide cuts and coating, polishing of internal parts, sight install, and optional match barrel fitment.

Fowler G19 Gen3 MARK 2 SS Match Barrel

$2,349.00
Our Complete Package is the ultimate choice for shooting enthusiasts who want the most out of their firearms. The complete package includes the base firearm along with all the alterations that make the Mark 2 the premier enhanced Glock platform. Treatment includes full grip work, slide cuts and coating, polishing of internal parts, sight install, and optional match barrel fitment.

Fowler G19 Gen3 MARK 2 TUNG SS Match Barrel

$2,349.00
Our Complete Package is the ultimate choice for shooting enthusiasts who want the most out of their firearms. The complete package includes the base firearm along with all the alterations that make the Mark 2 the premier enhanced Glock platform. Treatment includes full grip work, slide cuts and coating, polishing of internal parts, sight install, and optional match barrel fitment.

Agency Arms Glock 19 Gen 4 URBAN TUNGSTEN

$2,230.00
Slide Work All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed. This plate is designed in a way that enables one hand manipulation of the firearm that increases safety. We don’t do top serrations due to training issues with the masses. On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts. Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. ​ Internal Work We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring. We replace only one spring in the trigger system which is the plunger safety spring. The other springs are stock and will grant consistent primer strikes and positive reset. We use a factory OEM minus connector and tune the factory trigger bar. With all this work the pull weight will be 4-4.25 pounds depending on the pistol. We also manufacture our own trigger shoe which is flat with a curved toe. This fixes the issue of trigger/trigger guard finger and glove bite. Frame work We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill. We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol. With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster. We do a non traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge. PRODUCT TAGS

Agency Arms 20 G4 Hybrid Tungsten

$2,212.00
Slide Work All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed. This plate is designed in a way that enables one hand manipulation of the firearm that increases safety. We don’t do top serrations due to training issues with the masses. On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts. Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. ​ Internal Work We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring. We replace only one spring in the trigger system which is the plunger safety spring. The other springs are stock and will grant consistent primer strikes and positive reset. We use a factory OEM minus connector and tune the factory trigger bar. With all this work the pull weight will be 4-4.25 pounds depending on the pistol. We also manufacture our own trigger shoe which is flat with a curved toe. This fixes the issue of trigger/trigger guard finger and glove bite. Frame work We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill. We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol. With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster. We do a non traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Glock 17 GEN 4 FDE DLC

$2,199.00

Slide Work
All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed. This plate is designed in a way that enables one hand manipulation of the firearm that increases safety. We don’t do top serrations due to training issues with the masses. On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts. Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol.

Internal Work
We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring. We replace only one spring in the trigger system which is the plunger safety spring. The other springs are stock and will grant consistent primer strikes and positive reset. We use a factory OEM minus connector and tune the factory trigger bar. With all this work the pull weight will be 4-4.25 pounds depending on the pistol. We also manufacture our own trigger shoe which is flat with a curved toe. This fixes the issue of trigger/trigger guard finger and glove bite.

Frame work
We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill. We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol. With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster. We do a non traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 19 G3 Urban DTF Agency Grey

$2,174.00
Slide Work All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed. This plate is designed in a way that enables one hand manipulation of the firearm that increases safety. We don’t do top serrations due to training issues with the masses. On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts. Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. ​ Internal Work We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring. We replace only one spring in the trigger system which is the plunger safety spring. The other springs are stock and will grant consistent primer strikes and positive reset. We use a factory OEM minus connector and tune the factory trigger bar. With all this work the pull weight will be 4-4.25 pounds depending on the pistol. We also manufacture our own trigger shoe which is flat with a curved toe. This fixes the issue of trigger/trigger guard finger and glove bite. Frame work We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill. We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol. With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster. We do a non traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 19 G4 Urban Multicam

$2,159.00
Slide Work All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed. This plate is designed in a way that enables one hand manipulation of the firearm that increases safety. We don’t do top serrations due to training issues with the masses. On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts. Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. ​ Internal Work We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring. We replace only one spring in the trigger system which is the plunger safety spring. The other springs are stock and will grant consistent primer strikes and positive reset. We use a factory OEM minus connector and tune the factory trigger bar. With all this work the pull weight will be 4-4.25 pounds depending on the pistol. We also manufacture our own trigger shoe which is flat with a curved toe. This fixes the issue of trigger/trigger guard finger and glove bite. Frame work We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill. We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol. With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster. We do a non traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms Glock 26 Gen 4 Tungsten

$2,130.00

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms Glock 26 Gen 4 Tungsten

$2,130.00

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms M&P 9 BW Burnt Bronze

$2,119.00
Agency Arms presents a new build complete build package for the M&P platform. The build package includes many familiar features you see in our Glock builds. Each build also includes a set of custom Dawson Precision sights and Apex Tactical Specialties' internals for the trigger group. Slide Work All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed. This plate is designed in a way that enables one hand manipulation of the firearm that increases safety. We don’t do top serrations due to training issues with the masses. On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts. Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. Frame work We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill. We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol. With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster. We do a non traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling

AGENCY ARMS GLOCK 17 GEN 4 URBAN BLACK

$2,080.00
Gun Specific Options: -9mm Generation 4 -DLC Slide -Magwell (NBS) -(4) Stippled Backstraps -(3) 17rnd Magazines

AGENCY ARMS GLOCK 17 GEN 4 URBAN BLACK

$2,080.00
Gun Specific Options: -9mm Generation 4 -DLC Slide -Magwell (NBS) -(4) Stippled Backstraps -(3) 17rnd Magazines

AGENCY ARMS GLOCK 17 GEN 4 URBAN BLACK

$2,080.00
Gun Specific Options: -9mm Generation 4 -DLC Slide -Magwell (NBS) -(4) Stippled Backstraps -(3) 17rnd Magazines

Agency Arms 19 Gen 4 Silver Slide

$2,074.00
Slide Work All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed. This plate is designed in a way that enables one hand manipulation of the firearm that increases safety. We don’t do top serrations due to training issues with the masses. On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts. Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. ​ Internal Work We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring. We replace only one spring in the trigger system which is the plunger safety spring. The other springs are stock and will grant consistent primer strikes and positive reset. We use a factory OEM minus connector and tune the factory trigger bar. With all this work the pull weight will be 4-4.25 pounds depending on the pistol. We also manufacture our own trigger shoe which is flat with a curved toe. This fixes the issue of trigger/trigger guard finger and glove bite. Frame work We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill. We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol. With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster. We do a non traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 19 Gen 4 Green Frame

$2,049.00
Slide Work All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed. This plate is designed in a way that enables one hand manipulation of the firearm that increases safety. We don’t do top serrations due to training issues with the masses. On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts. Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. ​ Internal Work We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring. We replace only one spring in the trigger system which is the plunger safety spring. The other springs are stock and will grant consistent primer strikes and positive reset. We use a factory OEM minus connector and tune the factory trigger bar. With all this work the pull weight will be 4-4.25 pounds depending on the pistol. We also manufacture our own trigger shoe which is flat with a curved toe. This fixes the issue of trigger/trigger guard finger and glove bite. Frame work We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill. We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol. With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster. We do a non traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 19 Gen 4 Grey Frame

$2,049.00
Slide Work All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed. This plate is designed in a way that enables one hand manipulation of the firearm that increases safety. We don’t do top serrations due to training issues with the masses. On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts. Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. ​ Internal Work We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring. We replace only one spring in the trigger system which is the plunger safety spring. The other springs are stock and will grant consistent primer strikes and positive reset. We use a factory OEM minus connector and tune the factory trigger bar. With all this work the pull weight will be 4-4.25 pounds depending on the pistol. We also manufacture our own trigger shoe which is flat with a curved toe. This fixes the issue of trigger/trigger guard finger and glove bite. Frame work We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill. We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol. With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster. We do a non traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms G17 Gen 4 GREY Frame DLC

$2,049.00
Slide Work All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed. This plate is designed in a way that enables one hand manipulation of the firearm that increases safety. We don’t do top serrations due to training issues with the masses. On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts. Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. ​ Internal Work We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring. We replace only one spring in the trigger system which is the plunger safety spring. The other springs are stock and will grant consistent primer strikes and positive reset. We use a factory OEM minus connector and tune the factory trigger bar. With all this work the pull weight will be 4-4.25 pounds depending on the pistol. We also manufacture our own trigger shoe which is flat with a curved toe. This fixes the issue of trigger/trigger guard finger and glove bite. Frame work We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill. We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol. With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster. We do a non traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms G17 Gen 4 GREY Frame DLC

$2,049.00
Slide Work All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed. This plate is designed in a way that enables one hand manipulation of the firearm that increases safety. We don’t do top serrations due to training issues with the masses. On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts. Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. ​ Internal Work We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring. We replace only one spring in the trigger system which is the plunger safety spring. The other springs are stock and will grant consistent primer strikes and positive reset. We use a factory OEM minus connector and tune the factory trigger bar. With all this work the pull weight will be 4-4.25 pounds depending on the pistol. We also manufacture our own trigger shoe which is flat with a curved toe. This fixes the issue of trigger/trigger guard finger and glove bite. Frame work We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill. We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol. With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster. We do a non traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 26 G4 DLC

$2,049.00

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 26 G4 DLC

$2,049.00

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 26 G4 DLC

$2,049.00

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms G17 Gen 4 GREY Frame DLC

$2,049.00
Slide Work All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed. This plate is designed in a way that enables one hand manipulation of the firearm that increases safety. We don’t do top serrations due to training issues with the masses. On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts. Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. ​ Internal Work We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring. We replace only one spring in the trigger system which is the plunger safety spring. The other springs are stock and will grant consistent primer strikes and positive reset. We use a factory OEM minus connector and tune the factory trigger bar. With all this work the pull weight will be 4-4.25 pounds depending on the pistol. We also manufacture our own trigger shoe which is flat with a curved toe. This fixes the issue of trigger/trigger guard finger and glove bite. Frame work We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill. We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol. With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster. We do a non traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 17 G4 Dark Earth DLC

$2,049.00
Slide Work All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed. This plate is designed in a way that enables one hand manipulation of the firearm that increases safety. We don’t do top serrations due to training issues with the masses. On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts. Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. ​ Internal Work We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring. We replace only one spring in the trigger system which is the plunger safety spring. The other springs are stock and will grant consistent primer strikes and positive reset. We use a factory OEM minus connector and tune the factory trigger bar. With all this work the pull weight will be 4-4.25 pounds depending on the pistol. We also manufacture our own trigger shoe which is flat with a curved toe. This fixes the issue of trigger/trigger guard finger and glove bite. Frame work We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill. We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol. With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster. We do a non traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms M&P 9 Crushed Silver

$2,044.00
Agency Arms presents a new build complete build package for the M&P platform. The build package includes many familiar features you see in our Glock builds. Each build also includes a set of custom Dawson Precision sights and Apex Tactical Specialties' internals for the trigger group. Slide Work All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed. This plate is designed in a way that enables one hand manipulation of the firearm that increases safety. We don’t do top serrations due to training issues with the masses. On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts. Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. Frame work We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill. We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol. With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster. We do a non traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling

Agency Arms M&P 9 FDE

$2,044.00
Agency Arms presents a new build complete build package for the M&P platform. The build package includes many familiar features you see in our Glock builds. Each build also includes a set of custom Dawson Precision sights and Apex Tactical Specialties' internals for the trigger group. Slide Work All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed. This plate is designed in a way that enables one hand manipulation of the firearm that increases safety. We don’t do top serrations due to training issues with the masses. On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts. Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. Frame work We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill. We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol. With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster. We do a non traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling

Agency Arms M&P 9 DLC

$2,019.00
Agency Arms presents a new build complete build package for the M&P platform. The build package includes many familiar features you see in our Glock builds. Each build also includes a set of custom Dawson Precision sights and Apex Tactical Specialties' internals for the trigger group. Slide Work All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed. This plate is designed in a way that enables one hand manipulation of the firearm that increases safety. We don’t do top serrations due to training issues with the masses. On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts. Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. Frame work We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill. We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol. With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster. We do a non traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling

AGENCY ARMS GLOCK 17L GEN 3 Urban DLC

$1,999.00
Gun Specific Options: -9mm Generation 3 -Urban -DLC Coating -Magwell -Agency Backplate -(2) 17rnd Magazines

Agency Arms 19 G3 Urban Blue Titanium

$1,924.00
Slide Work All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed. This plate is designed in a way that enables one hand manipulation of the firearm that increases safety. We don’t do top serrations due to training issues with the masses. On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts. Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. ​ Internal Work We start by swapping out the recoil system with an ISMI stainless steel guide rod and flat wire recoil spring. We replace only one spring in the trigger system which is the plunger safety spring. The other springs are stock and will grant consistent primer strikes and positive reset. We use a factory OEM minus connector and tune the factory trigger bar. With all this work the pull weight will be 4-4.25 pounds depending on the pistol. We also manufacture our own trigger shoe which is flat with a curved toe. This fixes the issue of trigger/trigger guard finger and glove bite. Frame work We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill. We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol. With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster. We do a non traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 26 G3 DLC

$1,899.00

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Agency Arms 26 G3 DLC

$1,899.00

Slide Work

 

All of our slides have an RMR cut standard, and come with a “Battle Plate” that fills the void when the RMR is not installed.  This plate is designed in a way that enables one hand manipulation of the firearm that increases safety.  We don’t do top serrations due to training issues with the masses.  On our Battle Plate, the serrations and screw lugs are on the 45 angle cuts.  Placing these serrations and lugs here, forces the shooter to angle the pistol away from the body when using one hand to rack the pistol. 

 

Internal Work

 

We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, cut in gas pedals, and bevel out the inside area of the trigger guard on a mill.  We call the gas pedals the “Accelerator Cuts” and they offer enhanced traction on the pistol.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

AGENCY ARMS GLOCK 43 Hybrid TUNGSTEN

$1,855.00

Internal Work

 

We replace only one spring in the trigger system which is the plunger safety spring.  The other springs are stock and will grant consistent primer strikes and positive reset.  We use a factory OEM minus connector and tune the factory trigger bar.  With all this work the pull weight will be 4-4.25 pounds depending on the pistol.  We also manufacture our own trigger shoe which is flat with a curved toe.  This fixes the issue of trigger/trigger guard finger and glove bite.

 

Frame work

 

 We remove the finger grooves, and bevel out the inside area of the trigger guard on a mill.  With the accelerator cuts, muzzle rise is dramatically decreased and follow up shots are faster.  We do a non-traditional double undercut and dock the front of the trigger guard for aesthetic purposes. We finish the frame off with full stippling and offer Gen 4 back strap melding as well for no additional charge.

Wilson Combat Standard Shotgun GRAY

$1,540.00
The Standard Model incorporates the features many of our owners want most in their defensive shotguns, in a value-packed package.

FN FiveSeven LE

$1,200.00
NH USA FN Five-seveN® The FN Five-seveN® pistol was developed in the early 1990s and features a cold hammer-forged barrel that is chrome lined for extended service life. The polymer-framed FN Five-seveN® offers single-action operation, low felt recoil, 20-round magazine capacity and is equipped with an ambidextrous, forward-mounted manual safety and an accessory rail that accepts tactical lights and lasers.

Wilson Combat Border Patrol Shotgun GRAY

$1,135.00
The Border Patrol Model has an outstanding, well-earned reputation as the workhorse of Wilson Combat® / ScattergunTechnologies™ shotguns.

Deadair Silencers Wolverine PBS-1

$995.00
PEOPLE SAID IT COULDN’T BE DONE. You want to build a dedicated AK suppressor? “You can’t do that.” “They’re too loud.” “What about non-concentric threads?” “How will it mount consistently?” “There’s too many variations.” And yet, here it is. AK and combloc gun lovers rejoice. The Wolverine strikes the perfect balance between suppression and minimal back pressure. SO WHAT DOES THE WOLVERINE PBS-1 SILENCER FIT? You won’t have to buy multiple silencers to fit different threaded combloc rifles. The Wolverine offers user changeable thread inserts. The Wolverine ships with a 14L thread insert. We plan on making 14R, 24R, 26L, 15mm, 16mm, 1/2×28, 5/8×24, and 9/16L as well; and possibly more will be added to the list depending on demand.

Hoback/Alphahunter Collab Black Stallion WarHorse Folder, Titanium, 3.07" Blade DLC BLACK

$800.00
The Black Stallion WarHorse A Few Years Ago: I had been making folders for about 2 years when, in 2011, Chad of Alphahunter Tactical Design approached me about a project. That project was the WarHorse -- a honkin’ huge knife with a full 4” blade and massive slabs of .200 thick titanium! Chad and I went back and forth on design parameters for a few days, and the original WarHorse was born. We did several different variations on the design and even did a mini-flipper version. The design was amazingly popular, and we sold out of each run we made within days. A few years went by and Chad and I kept busy growing our respective businesses and doing other things on our own. All along, though, I’ve wanted to get back with him and make another run! Today: I’m proud to announce that Chad and I arranged our schedules to collaborate once again on another run. Plus, I pulled out all the stops in a redesign of the knife! I ran a full FEA (Finite element analysis) on it to check for any weak spots. Pocketed all non-structural components to get the weight down. Did a ground-up design of a perfect hardened lock insert. Even did a full Bio/Organic 3D machined semi-floating backspacer. Added my HRD (Hoback Roller Detent), HCP (Hoback Cammed Pivot), and hardened stainless bearing races. The result? A brand new WarHorse Chad has dubbed the “Black Stallion!” The WarHorse is Available in either a DLC Black Finish or a DLC Black Fallout Finish! The First 50 Knives in this Limited Edition will be Numbered! Plus... Every knife will be inscribed with Ps121 (Chad's pick)!

Hoback HERO SERIES OSF Authorized Dealer Exclusive Knife, 3.5" Blade

$550.00
"Authorized Dealer Exclusive OSF" This knife will be available only through our Authorized Dealers. Please click the "Notify Me" button to receive notification when our dealers receive them. The OSF3.5 has been one of those knives that has always had a huge following. OSF stands for "Open Source Folder." As Jake says, "When I started this project in 2010, it was after I had spent countless hours researching folding knives, mechanisms and lock geometry. I thought to myself, why not put this information into a solid model so that everyone who is getting into making folders can start with a finished idea to look at while they build their very own awesome knife. So I set out to make the knife in such a way that it could be made with simple tools, no CNC necessary. All you would need to do is waterjet cut a blank and start drilling and tapping." The knife design itself is a modified sheep’s foot blade with a properly engineered frame set. The single point rear standoff/backspacer is large enough to handle knife stresses but small enough to allow a rather large handle to blade ratio. The blade steel is CPM-S35VN, with an excellent heat treat that seamlessly flows into and out of the titanium frame set. There are several options to choose from to make this knife your very own -- including pocket clips, pivots, backspacers, and inlays. This all adds up to a NPD (Never Put it Down), not just an EDC!

2A BALIOS-LITE 556NATO RECEIVER SET

$520.00
With weight saving as the prime objective, 2A-Armament set out to build a lightweight solution for those looking for a solid platform to build on. The BALIOS-lite has all the same great features and aesthetics as our standard BALIOS sets, but incorporates a significant weight reduction. The BALIOS-lite is perfect for those who participate in 3-gun, hunting, or any other shooting activity where weight is a concern. Both the upper and lower receivers are equally at home on a standard forged product from other vendors. The flared magazine well aids in rapid reloading, and the tapered transition under the charging handle prevents associated wear patterns from damaging the finish. We have eliminated the forward assist, and retained the port door cover on the upper receiver.

Half Face Blades - Disaster Breacher W/ Bocote Handle

$495.00
Half Face Blades was founded by Andrew Arrabito, Navy SEAL (ret.), to meet the need for high-quality, “go to” knives and axes – usable, personalized, functional, versatile tools that work for every person in every walk of life. Andrew grew up hunting, camping and fishing in the great outdoors. After high school he joined the US Navy, determined to achieve the honor of serving in the United States Navy SEAL Teams. It was during his time in the Teams that Andrew decided to bring the “end user” back to the beginning, to learn blade-smithing. From the beginning, Andrew’s goal was to make simple blade designs for consumers who demand the finest products. With his real-world experience in using cutting devices in super-charged action, Andrew understands what will be demanded from his blades. And he makes them to meet those demands. Half Face Blades knives are designed with the distinction and ruggedness required for the work they are intended to do. Each knife is calculated to meet requirements gained by experience, by testing knives and axes, by using them over time at sea and in remote wildernesses. HFB knives bring the soul of rugged, dependable, combat knives and tools to a variety of settings - from special operations tools for warriors, hunters and backpackers, to knives for the kitchen and great American workers. “I wanted each person to have a usable tool, embodied with a warrior’s spirit, that will perform to their needs during their walk in life.”

Half Face Blades - Disaster Breacher W/ Blood Wood Handle

$495.00
Half Face Blades was founded by Andrew Arrabito, Navy SEAL (ret.), to meet the need for high-quality, “go to” knives and axes – usable, personalized, functional, versatile tools that work for every person in every walk of life. Andrew grew up hunting, camping and fishing in the great outdoors. After high school he joined the US Navy, determined to achieve the honor of serving in the United States Navy SEAL Teams. It was during his time in the Teams that Andrew decided to bring the “end user” back to the beginning, to learn blade-smithing. From the beginning, Andrew’s goal was to make simple blade designs for consumers who demand the finest products. With his real-world experience in using cutting devices in super-charged action, Andrew understands what will be demanded from his blades. And he makes them to meet those demands. Half Face Blades knives are designed with the distinction and ruggedness required for the work they are intended to do. Each knife is calculated to meet requirements gained by experience, by testing knives and axes, by using them over time at sea and in remote wildernesses. HFB knives bring the soul of rugged, dependable, combat knives and tools to a variety of settings - from special operations tools for warriors, hunters and backpackers, to knives for the kitchen and great American workers. “I wanted each person to have a usable tool, embodied with a warrior’s spirit, that will perform to their needs during their walk in life.”

Hoback OSF Authorized Dealer Exclusive Knife, 3.5" Blade

$495.00
"Authorized Dealer Exclusive OSF" This knife will be available only through our Authorized Dealers. Please click the "Notify Me" button to receive notification when our dealers receive them. The OSF3.5 has been one of those knives that has always had a huge following. OSF stands for "Open Source Folder." As Jake says, "When I started this project in 2010, it was after I had spent countless hours researching folding knives, mechanisms and lock geometry. I thought to myself, why not put this information into a solid model so that everyone who is getting into making folders can start with a finished idea to look at while they build their very own awesome knife. So I set out to make the knife in such a way that it could be made with simple tools, no CNC necessary. All you would need to do is waterjet cut a blank and start drilling and tapping." The knife design itself is a modified sheep’s foot blade with a properly engineered frame set. The single point rear standoff/backspacer is large enough to handle knife stresses but small enough to allow a rather large handle to blade ratio. The blade steel is CPM-S35VN, with an excellent heat treat that seamlessly flows into and out of the titanium frame set. There are several options to choose from to make this knife your very own -- including pocket clips, pivots, backspacers, and inlays. This all adds up to a NPD (Never Put it Down), not just an EDC!

AGENCY ARMS BONESAW AUTHORIZATION FEE

$150.00

Note: This is the ONLY way to order the "Bonesaw" cuts on a CUSTOMER SUPPLIED gun through Agency Arms.

We are accepting Authorization Fee's for Agency Arms to gunsmith a customer supplied Glock pistol finished in the Reactive Gunworks exclusive "Bonesaw" cut.

Customer Supplied Process:
1) Pay the "Bonesaw Authorization Fee" to Reactive Gunworks (each fee entitles you to the design rights for 1 pistol)

2) Using your Order Confirmation code from Reactive Gunworks, place your Bonesaw order directly with Agency Arms and pay the required 50% deposit (at www.AgencyArms.com)

3) Mail your Glock directly to Agency Arms (you will receive shipping instructions directly from Agency)

4) Upon completion of the gunsmithing by Agency Arms, pay the remaining balance due and Agency Arms will return ship your firearm.

How long will it take?
Build Times are provided by Agency Arms and are based off Demand.

Not available on subcompact (ie.G42/43) or long slide (ie.G34/17L) or large

Filter by:

Clear All

Filter by